Updated November 2026

Smoking steaks in a smoker gives you a deep, wood-kissed flavor and a rosy, edge-to-edge center that’s hard to get from a grill alone. The method is simple: cook the steak low and slow until it hits your target internal temperature, then finish with a hot sear. This guide covers the setup, the temperatures, and the finishing step that makes the crust.

Choose the Right Steak and Prep It

Thick cuts work best for smoking. Aim for ribeye, strip, sirloin, or filet at least 1.5 inches thick, since thin steaks overcook before they pick up much smoke. Pat the steak dry, season it generously with salt and pepper or your favorite steak rub, and let it rest uncovered on a rack in the fridge for 30 to 60 minutes. The dry surface helps the rub stick and the crust form later.

Shopping for one? See our guide: Pellet Grill vs Electric Smoker (2026): Which Is Better for Smoking?.

Set Up the Smoker for Low and Slow

Preheat your smoker to between 225°F and 250°F. Use a mild wood such as oak, hickory, or cherry for steak; heavy woods like mesquite can turn bitter over a long cook. If you use a pellet grill, a mild hardwood pellet blend works well. Give the smoker 15 to 20 minutes to stabilize before the steaks go on, and set the grate as close to the heat source as your unit allows.

Monitor Internal Temperature, Not Time

Time per pound varies too much to rely on. Use a leave-in or wireless probe and pull the steak when it reaches your target:

  • Rare: 120°F to 125°F
  • Medium-rare: 130°F to 135°F
  • Medium: 140°F to 145°F

Thick steaks often take 60 to 90 minutes in the smoker. Expect the temperature to climb a few degrees after you pull it, so take it out a little early.

Sear for the Crust

Smoked steak won’t brown on its own, so finish over high heat. Crank a grill or cast iron pan to as hot as it goes, about 500°F or higher, and sear 60 to 90 seconds per side. Some pitmasters use the reverse sear method in reverse order, but the principle is the same: low heat for the interior, high heat for the crust. Rest the steak 5 to 10 minutes before slicing so the juices stay put.

Steps at a Glance

  1. Dry and season the steak, then rest it uncovered in the fridge.
  2. Preheat the smoker to 225°F to 250°F with a mild wood.
  3. Smoke until the internal temperature reaches your target.
  4. Sear over the hottest heat you can reach for 60 to 90 seconds per side.
  5. Rest for 5 to 10 minutes, then slice against the grain.

Common Mistakes

  • Using steaks thinner than 1 inch, which overcook before they absorb smoke.
  • Cooking by time instead of probe temperature.
  • Skipping the sear, which leaves the surface pale and soft.
  • Oversmoking with strong woods or too much smoke at the start.
  • Slicing immediately, which lets the juices run onto the board.

A reliable leave-in probe thermometer removes the guesswork from doneness. View on Amazon

A cast iron skillet gives you a strong, even sear when your grill can’t reach high enough. View on Amazon

FAQ

Can I smoke a steak at a higher temperature to save time?

You can, but temperatures above 275°F tend to gray the outer band and produce less even doneness. Low and slow gives the cleanest results for steaks.

Do I need to flip the steak while smoking?

Flipping isn’t required. One flip halfway through can help even out cooking on uneven grates, but most cooks leave it alone until the sear.

Should I smoke steak with the lid open or closed?

Keep the lid closed as much as possible to hold temperature and steady the smoke. Open it only to check the probe or add wood.

Conclusion

Smoking steaks in a smoker comes down to three things: a thick cut, a steady low temperature, and a hot sear at the end. Pull by internal temperature, rest the meat, and you’ll get consistent results. Start with ribeye or strip to learn your smoker’s habits, then adjust the wood and doneness to suit your taste.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our BBQ & grilling guides, checking product details against manufacturer specifications and owner feedback.