Updated November 2026

A Pit Boss pellet grill auger motor moves pellets from the hopper into the firepot. When it stops, the fire starves and the grill can’t hold temperature. This guide walks you through confirming the motor is the problem, checking the wiring and control board, and replacing the motor if it has failed.

Confirm the Auger Motor Is the Problem

Before buying parts, rule out simpler causes. Turn the grill on and watch the auger through the hopper opening or the firepot. You should see it rotate and feed pellets when the grill is in startup or cooking mode. Listen for the motor’s hum as well.

Shopping for one? See our guide: Pellet Grill vs Electric Smoker (2026): Which Is Better for Smoking?.

If the auger does not move but the fan and igniter run, the motor, its wiring, or the controller output is the likely culprit. If the auger turns but pellets don’t reach the firepot, the problem is more likely a jammed auger tube or a bridged hopper.

Test the Motor and Wiring

Unplug the grill and let it cool completely before you open the back panel. Pellet grill controllers carry line voltage, so take your time and work carefully.

  1. Disconnect the auger motor’s plug and set a multimeter to continuity or resistance.
  2. Measure across the motor’s two terminals. A reading of open circuit (no continuity) means the internal winding has failed.
  3. Check the wire harness for melted insulation, loose crimps, or scorched plugs. Pellet dust and heat often damage these connectors.
  4. If the motor shows continuity, plug it back in and check voltage at the connector while the grill calls for the auger. No voltage points to the controller or board.

Refer to your model’s wiring diagram, and if you are not comfortable working with mains-powered controllers, consult a qualified appliance technician.

Replace the Auger Motor

Replacement parts are usually sold by Pit Boss or through authorized parts dealers. Match the part to your exact model number, which is printed on the rating label inside the hopper or on the back panel. Using the wrong motor can cause jamming or poor feed rates.

  • Basic socket and nut driver set
  • Multimeter
  • Replacement auger motor matched to your model
  • Small bowl for stored screws and fasteners
  • Vacuum to clear pellet dust from the firepot and auger tube

Remove the motor mounting bolts, disconnect the harness, and transfer the auger coupling to the new motor if your design requires it. Reassemble, reconnect power, and run a short startup test with the hopper cover off so you can watch the auger turn.

Common Mistakes

  • Replacing the motor without checking for a jammed auger tube or a wet pellet clog.
  • Forcing the auger by hand while the grill is powered.
  • Ignoring a burnt or loose connector, which can fail the new motor quickly.
  • Storing the grill with pellets in the hopper, which encourages moisture and swelling.
  • Skipping routine cleaning of the firepot and auger, which adds drag on the motor.

A basic digital multimeter makes it easy to check continuity and voltage without guessing. A small shop vacuum helps clear pellet dust from the auger channel and firepot before you reassemble.

View on Amazon

View on Amazon

FAQ

Can I clean the auger instead of replacing the motor?

Yes, if the auger is jammed rather than the motor being dead. Unplug the grill, clear the hopper and tube, and test again before ordering parts.

How do I know if the controller is at fault?

If the motor reads good on continuity but gets no voltage when the grill calls for the auger, the controller or board is the likely problem.

Should I replace the auger motor myself?

Many owners handle it with basic tools, but the wiring carries mains voltage. If you are unsure, have a qualified technician do the work.

Conclusion

Confirm the auger is actually stalled, test the motor and its wiring, and only then replace the motor if it has failed. Keep the firepot and auger clean to extend the life of the new part. For related repair steps, see Pit Boss Pellet Grill Repair: A Step-by-Step Troubleshooting Guide and Essential Pellet Grill Maintenance: Cleaning the Firepot and Auger.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our BBQ & grilling guides, checking product details against manufacturer specifications and owner feedback.