Updated November 2026

To cook ribs on a gas grill, you set up two heat zones, keep the lid closed at a steady 250 to 275°F, and cook the ribs over indirect heat for roughly 4 to 5 hours. The result is tender meat that pulls cleanly from the bone, with a sticky, lightly charred glaze. This guide covers the setup, the cook, and the finish.

Choose the Right Ribs and Prep Them

Baby back ribs cook faster and are the easier choice for a first attempt, usually finishing in about 4 hours. St. Louis-style spare ribs have more fat and connective tissue, so they need closer to 5 hours but reward patience with more flavor. Either works on a gas grill as long as you control the temperature.

Shopping for one? See our guide: Top 6 Propane Gas Barbecue Grill Picks for Backyard Cooks in 2026.

Remove the thin membrane on the bone side. Slide a butter knife under one corner, lift, and pull it off with a paper towel for grip. Then coat the ribs with a binder such as yellow mustard or olive oil, and season generously with your rub. Let them sit at room temperature for 30 minutes while the grill heats.

Set Up the Gas Grill for Indirect Heat

Ribs need low, even heat that surrounds the meat rather than hitting it from below. Here is how to set that up:

  1. Preheat all burners on high for 10 to 15 minutes with the lid closed.
  2. Turn off the burner or burners under one side, leaving the other side on to create a direct zone and an indirect zone.
  3. Adjust the burners on the lit side until the grill’s internal thermometer reads 250 to 275°F on the indirect side.
  4. Place a foil drip pan under the grate on the unlit side, filled with water, apple juice, or beer, to add moisture and catch drippings.
  5. Scrub the grates clean and oil them lightly so the ribs do not stick.

Smoke the Ribs Low and Slow

Place the ribs bone-side down on the indirect side, away from the lit burners. Close the lid and leave it alone for the first 2 hours. Opening it often drops the temperature and adds time.

If you want smoke flavor, use a smoker box or a foil pouch of soaked hardwood chips such as apple, cherry, or hickory over the lit burner. Refill with chips every hour or so if you want a steady smoke. Keep the wood away from direct flame so it smolders rather than burns.

Wrap, Sauce, and Check for Doneness

Around the 2 to 2.5 hour mark, the bark should be set and deep reddish-brown. Some cooks wrap the ribs in foil with a splash of liquid, a method often called the 3-2-1 approach, but you can skip it for a firmer, more textured bark. If you wrap, do it once and return the ribs to the grill for the remaining time.

Brush on sauce during the final 20 to 30 minutes, not earlier, since sugar burns. Ribs are done when the meat has pulled back about a quarter inch from the bone ends and a probe slides in with little resistance, usually around 195 to 203°F internal. Rest them for 10 minutes before cutting.

Common Mistakes

  • Cooking over direct flame, which dries and scorches the meat before the connective tissue breaks down.
  • Running the grill too hot. Above 300°F, ribs tighten up and can taste tough.
  • Skipping the membrane removal, which leaves a chewy layer.
  • Adding sauce too early, which causes burnt, bitter patches.
  • Trusting the lid thermometer alone. Use a separate probe thermometer at grate level.
  • Digital probe thermometer: Lets you monitor grate and meat temperature without lifting the lid. View on Amazon
  • Smoker box for gas grills: Holds wood chips and produces steady smoke over a burner. View on Amazon
  • Foil drip pan: Catches drippings and holds water to keep the cooking chamber moist. View on Amazon

FAQ

Can I cook ribs on a gas grill without wood chips?

Yes. Ribs will still be tender and flavorful from the rub, low heat, and drippings alone. Wood chips add a smoky layer but are optional.

How long do ribs take on a gas grill?

Baby back ribs usually take about 4 hours and spare ribs about 5 hours at 250 to 275°F. Check doneness by feel and internal temperature rather than the clock alone.

Should I cook ribs meat side up or down?

Start bone side down on the indirect side, since that protects the meat from the heat. Flip only if your grill has hot spots that brown one side too quickly.

Conclusion

Cooking ribs on a gas grill comes down to two-zone heat, steady temperature, and patience. Hold the grill near 250 to 275°F, skip early sauce, and pull the ribs when they are tender rather than when the timer says so. For more on keeping your grill in shape, see How to Deep Clean Your Gas Grill’s Burners and Grates and How to Clean Gas Grill Grates in 20 Minutes: A Step-by-Step Guide.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our BBQ & grilling guides, checking product details against manufacturer specifications and owner feedback.