Updated November 2026
BBQ with Franklin brisket means cooking a whole packer brisket the way Aaron Franklin’s Austin-style barbecue does it: a simple salt-and-pepper rub, low-and-slow indirect heat, a long wrap-free stall, and a long rest before slicing. Follow the steps below and you’ll end up with a dark, peppery bark, a pink smoke ring, and slices that hold together but pull apart easily. The method is straightforward, but timing and temperature control do most of the work.
Prep the Brisket: Trim and Season
Start with a packer brisket in the 12 to 15 pound range, which includes both the flat and the point. Trim the hard fat cap to about a quarter inch, and remove any loose or silver-skin membrane on the flat side. Leave the fat on the point, since it renders into the meat during the long cook.
Shopping for one? See our guide: Lane's BBQ Brisket Rub: 5 Best Options for Texas-Style Brisket (2026).
Season generously with coarse black pepper and kosher salt, roughly a 1:1 ratio by volume, and press it in so it sticks. Many pitmasters season the night before and refrigerate uncovered so the surface dries slightly, which helps bark form. If you want a starting point for a store-bought option, compare the Authentic Texas-Style Smoked BBQ Brisket: A Step-by-Step Guide method for seasoning ratios.
Set Up the Smoker for Brisket Temperatures
Hold your cooking chamber at 250 to 275°F, using oak or another mild hardwood for a clean, steady smoke. Keep the meat away from direct flame and place the fat side up if your heat comes from below. Use a leave-in probe thermometer in the thickest part of the flat and a second probe in the point so you aren’t guessing.
- Preheat the smoker for 30 minutes, stabilizing at your target temperature.
- Place the brisket fat side up, away from the firebox.
- Smoke unwrapped until the bark is deep mahogany, usually 4 to 6 hours.
- Expect a stall around 160 to 170°F internal. Be patient; it can last several hours.
- Once the flat hits roughly 195 to 203°F and probes slide in with little resistance, pull it.
Manage the Stall and Wrapping Decision
The stall happens as moisture evaporates from the surface and cools it. Franklin-style cooks typically leave the brisket unwrapped to build bark rather than wrapping in butcher paper early. If bark gets too dark before the stall ends, you can wrap in unwaxed pink butcher paper at that point, not foil, which traps steam and softens the crust.
Don’t rely on time alone. A brisket that reaches temperature in six hours and one that takes fourteen can both be correct. Feel the probe for tenderness rather than watching the clock.
Rest, Slice and Serve
Rest the brisket for at least one hour, and longer if you can. Wrap it in towels and hold it in a faux cambro, cooler or warm oven around 150°F. Resting lets the juices redistribute and the connective tissue finish softening.
Slice against the grain in pencil-thick slices for the flat and chunkier pieces for the point. Keep the slices in order on the cutting board so the bark and fat stay with the cut they belong to.
Recommended gear
- Leave-in dual-probe thermometer: Lets you watch the flat and point temperatures without opening the smoker. View on Amazon
- Unwaxed pink butcher paper: Used for wrapping during the stall to protect bark while letting some steam escape. View on Amazon
- Coarse black pepper and kosher salt: The only seasoning the traditional method needs. View on Amazon
Common Mistakes
- Cooking at too high a temperature, which dries out the flat before the point renders.
- Wrapping in foil early, which steams the bark into a soft texture.
- Slicing before the rest, which lets juice run out onto the board.
- Pulling based on time or a fixed internal temperature instead of probe tenderness.
- Using too much smoke wood, which can make the bark bitter.
FAQ
Do I need to use a water pan for Franklin-style brisket?
A water pan can help keep humidity up and slow surface drying, but it isn’t required. Many cooks skip it and rely on steady temperature control instead.
Can I cook a brisket Franklin-style in a gas grill?
Yes, with indirect two-zone heat and a wood smoker box for flavor. Maintain 250 to 275°F and monitor it closely, since gas setups can run hotter and drier.
How do I know when the brisket is done?
Probe the flat and point, and pull when they slide in with little resistance, typically between 195 and 203°F. Consult a food safety reference for handling and holding guidelines if you’re serving a crowd.
Conclusion
Cooking BBQ with Franklin brisket comes down to good trimming, a simple salt-and-pepper rub, steady low heat and patience through the stall. Rest the meat thoroughly before slicing. Once you’ve done it a few times, you’ll learn to read your own smoker and your own meat.

